IBM error fault code-IBM User Need to Know

IBM error fault code
As an IBM User,we will meet the laptop break down some time.we don’t know what to do,because we don’t know which parts is break.now, i tell you the mean of IBM error code,so you can find where the question arises.if you alway concerned our blog,you will become a proficient in laptop parts
Symptom / Error ,FRU / Action in Sequence=10X101: Interrupt failure；102: Timer failure；103: Timer interrupt failure；104: Protected mode failure；105: Last 8042 command not accepted；107: NMI test failure；108: Timer bus test failure.109: Low meg-chip select test. 1. System board.110 : (Planar parity.) 1. Go to Memory Checkout 2. DIMM card.3. Detach the expansion unit if it is attached to the computer.4. laptop motherboard.111: (I/O parity.) 1. Go to Memory Checkout2. Expansion unit or port replicator.3. System board.11XX1101: Serial_A test failure. 1. Serial device2. Communication cable 3. System board12XX1201: Serial_B test failure. 1. System board (infrared)158 : (Hard disk password was not set even though the supervisor password is set.) （ 1. Set the password for hard disk drive.159 : (Hard disk password is not set the same as the supervisor password.) 1. Set the correct password for hard disk drive.161: (Dead battery. 1. Go to Checking the Backup Battery2. Backup battery.3. System board.163: (Time and date were not set. 1. Set time and date. 2. laptop motherboard.173: (Configuration data was lost.) 1. Select OK in the error screen; then set the time and date.2. Backup battery. 3. System board.174: (Configuration error: Perform Checking the Installed Devices List before changing any FRUs.) 1. Check device configuration.2. Hard disk drive assembly.3. System board.1751772. Diskette drive assembly. 3. Diskette. 4. System board.602: (Diskette read error.)； 1. Go to Diskette Drive Checkout2. Diskette.3. Diskette drive assembly.604: (Unacceptable ID was read from the diskette drive.)； 1. Go to Diskette Drive Checkout2. Diskette drive assembly.3. System board.2402 1. TV Out Card 24XX(2401: System board video error.) ； 1. System board. 808X8081: PCMCIA presence test failure.(PCMCIA revision number also checked.)8082: PCMCIA register test failure. 1. PC Card slot assembly.2. PCMCIA device.3. System board. 860X(Pointing device error when TrackPoint is disabled.)；8601: System bus error-8042 mouse interface.8602: External mouse error.；8603: System bus error or mouse error. ； 1. External mouse. ；2. External keyboard. ；3. System board.；861X(Pointing device error when TrackPoint is enabled.)；8611: System bus error-I/F between 8042 and IPDC.8612: TrackPoint error.8613: System board or TrackPoint error. 1. Reseat the keyboard cable on the subcard.；2. Keyboard ；3. External mouse ；4. Sub card ；5. System board ；I9990301I9990302I9990305I9990301: Hard disk error. ；I9990302: Invalid hard disk boot record.；I9990305: No bootable device. ； 1. Check that the operating system is installed in the hard disk drive. If not, install the operating system.；2. Reseat the boot device.3. Check the startup sequence for the correct boot device.；4. Check that the operating system has no failure and is installed correctly.；I9990303(Bank-2 flash ROM check sum error.) 1. System board.Other codes not listed above. 1. Go to Undetermined Problems178175: EEPROM CRC #1 error.177: Supervisor password check sum error.178: EEPROM is not functional. 1. System board.17XX1701: Hard disk controller failure.1780, 1790: Hard disk 0 error.1781, 1791: Hard disk 1 error. 1. Hard disk drive2. System board183 : (Incorrect password entered at the supervisor password prompt.) 1. Have the user examine the password.184: (Power-on password check sum error.) 1. Reset the power-onpassword in Easy-Setup.185: (The startup sequence is not valid. Suspect that power was off when the startupsequence was being updated.) 1. Reset the startup sequence in Easy-Setup.186 :1. System board. 190:(A depleted battery pack was installed when the power was on.) 1. Go to Checking the Battery Pack.191XX: (PM initialization error.) 1. laptop motherboard.192: (Fan error.) 1. Measure the voltage of the backup battery. If the voltage is not correct, replace the backup battery. 2. Fan 3. System board195: (The configuration read from the hibernation area does not match the actual configuration.) 1. Check if the configuration was changed. For example, check if the DIMM card is added.
196: (A read error occurred in the hibernation area of the hard disk drive.)1. Run the hard disk drive test.2. Hard disk drive. 199XX(Resume error.) 1. System board.1XX 1. System board. 2XX 201: Memory data error.202: Memory line error 00-15.203: Memory line error 16-23.205: Memory test failure on on-boardmemory.221: ROM to RAM remap error. 1. Go to Memory Checkout.2. DIMM card.3. System board. 225(Unsupported memory module.) 1. Check if the supported DIMM is installed.2. DIMM card.3. laptop motherboard.301, 303, 304, 305, 3XX
(301: Keyboard error.) 1. Go to Keyboard or Auxiliary Input Device
Checkout2. Keyboard.3. External numeric keypad.4. External laptop keyboard.5. Keyboard/mouse cable.6. System board.601, 6XX(601: Diskette drive or controller error.)1. Go to Diskette Drive Checkout.
Related Posts:
How to deal with minipci network card 1802 error
How to Upgrade THINKPAD 600E CPU To PⅢ 850
The HP NC4400 Laptop Drive for Window XP
How to search and replace your Laptop Motherboard
What is BIOS?
Laptop Troubleshooting -Laptop No Power Solution(4)
Dream laptop IBM ThinkPad W700
how to test laptop lcd screen
Laptop Boot theory (1)
How to buy and Replace a cover for your laptop
From laptop parts blog at www.laptoppartwholesale.com, post IBM error fault code-IBM User Need to Know
Post Footer automatically generated by wp-posturl plugin for wordpress.

Tags: laptop motherboard, laptop parts, laptop parts knowledge, System board, THINKPAD