HP NC6000 laptop motherboard MAX1987 chip poor Soldering

HP NC6000 laptop motherboard MAX1987 chip poor SolderingPhenomenon:1.electric current fall(the electric current from 0.8A to 0.4A) or the electric current jumped to 0.9a and then power failure.2.sometimes we can be power on this laptop,sometimes we cann’t.
Failure: CPU power-supplies chip (such as MAX1987 Chip) is poor soldering or be damage.the picture 1 show the position of MAX1987 chip in laptop motherboard,the power slot is outlined in blue on the picture 1,.the picture 2 show MAX1987 chip.picture 1
picture2
Failure Analysis:1.Operating Current of CPU power-supplies chip is too big ,normal operating current is 10A-20A and the CPU Operating voltage is about 1V,CPU is A main heat source of laptop motherboard.the pin(foot) and packaging of chip lead to the CPU power-supplies chip be poor soldering easily.2.other factor,the position of the power slot on HP NC6000 laptop motherboard is proximity MAX1987 chip.when we Frequent plug and pull the power wire,the area nearby power slot is squeezed cause poor soldering of MAX1987.
the solution thereof:MAX1987 chip is soldered again.if the chip was damage,you need replace a new MAX1987 chip on your laptop motherboard.

Tags: chip, laptop motherboard, max1987

How to deal with HP DV2000 laptop GPU overheating

1)One long beep and two short beeps indicates that the GPU chip is not working.2）I opened it up myself and found that the thermal pads on the CPU and mainly on the GPU had seemed to be making poor contact. The GPU contact in particular is rediculously bad – it has a paste type stuff that is about 2mm think and then the heatsink on top of that. I replaced everything with artic silver. Mine now works 100% everytime and doesnt get as hot as it used to do.3）I have found that the GPU gum between the GPU and the heatsink is meant to fill about a 2mm gap, but the gum dries out and cracks. When this happens the chip overheats, and the BGA pins on the gpu loose there connection. If you leave the power on after the beeping and block the vents a bit, the GPU/CPU heat sink warms up enough to expand the solder on the BGA pins and make a connection and the laptop will run. But eventually the solder will fully fracture, and a ball may come off and then you are totally stuffed.Fixing the heat sink does not fix the problem – its the cause of the problem though, so if you do get yours fixed, I would recommend opening it, scrapping off the blue gum, and inserting a 2mm peice of copper plate on-top of the GPU and using siler thermal paste to connect the GPU to the copper plate and then again on the other side to connect to the heatsink. But this won’t fix it if its already dead. (I tried it and I get the same long beep, two short beep).To fix the problem you have to re-flow the solder on the BGA. This should be done as a last resort (after your laptop doesnt turn on any more even when you heat it up). You have to strip down laptop to the motherboard. Bake the motherboard in a fan forced over at 80 degrees celcius for at least 24 hours (to get rid of any moisture that might be in the chip or solder). Immediatly after you take it out of the over, you need a hot air gun capable of reaching about 300 degrees. Heat the entire GPU chip and its board (don’t worry – all components can take 300 degress celcius for solder-reflow and did when the board was made). Keep bumping the GPU chip very slightly with a small screw driver, it will eventually become loose. Don’t lift it up however. Just keep the heat on for a few seconds to let the solder reflow and make a connection with the balls underneath.
After that let it cool down and plug everything back in and it *Might* work. If not can you heat it up and try again.HP should never have used a BGA chip for the GPU. Its rediculous considering how hot the chip gets. I think nvidia are partially at fault as well – the 7200 uses to much power to be a bga chip.
Goto the HP website and download the repair manual. It will tell you how to strip down to your motherboard. Take out the CPU and the heat sink fan assembly. Take everything connected to the motherboard off. Take out the RAM. Bake the motherboard in an oven at 80 degrees celcius. The older your board the longer you should bake it. I baked mine which is 16 months old for 16 hours. The actual recommended time is 24-48 hours if you want to be really safe. The point of baking is to remove moisture that might be in or around that chip that can explode if you heat past 100 degrees.
Next use alcohol to squirt under the nvidia GPU chip. Let it dry and squirt under there with solder flux. Place a light weight peice of metal on the GPU chip to weigh it down (I used a 10c coin),\. Next use a thermoeter and a hot air gun to heat the GPU chip to 190 degrees celcius. This is the reflow temperature of solder. At this temperature the little connections under neath the chip (the ball grid array) will go molten and reconnect. The idea is to heat it slowly till about 195, then thats it. Take the heat away and let it cool down and it will run.
MOST IMPORTANT TO ANYONE WHO FIXES THEIRS, EVEN IF HP FIX IT:The problem is caused by dust clogging in the heat sink assembly. Unfortuently you can only get to the dust by removing the fan, to remove the fan you must remove the heatsink. To remove the heat sink you have to re-apply thermal paste to the GPU and CPU, not to mention stripping your entire laptop down to access the motherboard. So if you don’t want yours to fail again, make sure to strip it down and take the fan off the heat sink and clean the dust out at least every 6 months. The laptop should NEVER get to hot to touch. If it is you almost certain have dust clogging the air flow. Inside the heat sink up against the copper cooling blades you will find they are clogged with dust. If you keep it free it of dust it never over heats.The GPU itself is not overheating and failing, this is probably why the PC happily runs and does not thermally shut down.
Whats happening is, because there is a gap filled with thermal paste, as the GPU gets hot, the solder is allowed to expand, as the heat sink is not locking it down. Instead the GPU moves upwards as the solder expands bh it and pushes the thermal gum away. Then when you turn it off, the gum sort of holds the GPU up against the heat sink, so the solder cools and has to pull the GPU chip back down. Eventually this causes the solder to fracture, as they are continually being pushed and pulled on. It doesnt happen on the CPU because the CPU is screwed directly onto the heat sink. Where as the GPU has that 2mm gap filled with blue heat gum.This is an obvious design error. The way they have a 2mm gap filled with gum is rediculous. Even if they fix it, it will happen again and again and again. Other message boards have had people who have taken there back 2 times or more now.
Fixing the dust will probably just prolong the time until it fails. I stronly recommend to remove the gum and use a 2mm plate of copper. Use thermal silver on each side. btw im electronics engineer and it still took me ages to figure out exactally what was wrong. You might have to grind down the copper to the right size. If it is too big, the heatsink my not clamp down on the CPU/GPU, if its to small it may slide out.
Related Posts:
HP NC6000 laptop motherboard MAX1987 chip poor Soldering
cool down your laptop fan and heatsink
How to search and replace your Laptop Motherboard
The most common of frequency value of laptop chip
How to Upgrade THINKPAD 600E CPU To PⅢ 850
How to Replace IBM Thinkpad Cooling Fan
What is BIOS?
BIOS chip model number, capacity, voltage, type
How to buy and Replace a cover for your laptop
How to disassemble laptop ,step by step guide!
From laptop parts blog at www.laptoppartwholesale.com, post How to deal with HP DV2000 laptop GPU overheating
Post Footer automatically generated by wp-posturl plugin for wordpress.

Tags: chip, fix, GPU, overheat

2009 total eclipse of the Sun in china

The longest solar eclipse in the last hundred years pitched a swath of Asia into near darkness Wednesday as millions gathered to watch the phenomenon.this total eclipse of the Sun is an unforgettable sight and give a strongly mind shock to people.Total solar eclipse in 2009 because so long time (up to more than 6 minutes),because the moon arrived perigee before the start of solar eclipse.In such a close distance,The moon looks bigger by 8% than the sun.I make a joke with my boss.”today have 2 day and 1night,so you shall pay me 3 times the wages.”
let we enjoyed this solar eclipse follow these photos.
if you still not got 3 times wages,quickly go to your boss office.
Related Posts:
Laptop Troubleshooting -Initial Troubleshooting
Repair and Remove IBM Thinkpad X22 lid hooks and hinges
How to disassemble laptop ,step by step guide!
Dismantle antediluvian IBM ThinkPad X22
HOW TO CHOOSE LAPTOP BATTERY- realize from Parameter to Cell.
BIOS chip model number, capacity, voltage, type
Dream laptop IBM ThinkPad W700
4 main data bus of Bios circuit diagram
What is BIOS?
cool down your laptop fan and heatsink
From laptop parts blog at www.laptoppartwholesale.com, post 2009 total eclipse of the Sun in china
Post Footer automatically generated by wp-posturl plugin for wordpress.

cool down your laptop fan and heatsink

Recently, our engineer found many laptop fans and heatsinks coverd with much dust when they repaired. This situation will make your computer more higher temperature. Thus affecting the status of its work. It is very important to cool down for your laptop, special in summer.so we teach you how to clear dust for your laptop fan and heatsink.
1. remove the cover plate of the power switch
2. remove the screws and the lines of keyboard, remover the laptop keyboard from the host( how to remove the keyboard please reference How to remove and repleace your laptop keyboard!)
3. remove the screws on the back of the laptop
4. remove the line of screen, remove the screen from the host
5. remove the bluetooth
6. remove the touch pad, firstly remove hard disk, you will see the screws, remove them. also remove the screws which fixed touch pad at the bottom of laptop.
7. remove the line of touch pad from laptop motherboard before you remove the touch padPlease note, you also need remove the line between BIOS battery and laptop motherboard.
8.remove the heatsink of CPU as the picture
9.remove wireless lan, modem,cpu,pccard,microphone,loudspeaker,motherboard as followed. you can remove laptop fan at last.
10. clear the dust for heatsink and laptop fan with brush.
Related Posts:
Repair and Remove IBM Thinkpad X22 lid hooks and hinges
Dismantle antediluvian IBM ThinkPad X22
4 main data bus of Bios circuit diagram
Dream laptop IBM ThinkPad W700
HP NC6000 laptop motherboard MAX1987 chip poor Soldering
How to remove and repleace your laptop keyboard!-www.laptoppartwholesale.com
How to deal with HP DV2000 laptop GPU overheating
Laptop Boot theory(2)
Laptop Troubleshooting -Laptop No Power Solution(3)
HOW TO CHOOSE LAPTOP BATTERY- realize from Parameter to Cell.
From laptop parts blog at www.laptoppartwholesale.com, post cool down your laptop fan and heatsink
Post Footer automatically generated by wp-posturl plugin for wordpress.

Tags: BIOS, cool, Laptop Fan, laptop heatsink, Remove

How to deal with minipci network card 1802 error

How to deal with minipci network card 1802 errorIBM ThinkPad laptop use an non-built-in wireless network card that not be Proven by IBM.(mean it is not original wireless network card ),this laptop probably show 1802 error.Don’t worry,I tech you how to deal with this problem.1.After the heavy start puts in the first compact disc the light to drive, then starts by the compact disc,and enter DOS(pure DOS,not pure-DOS in window XP environment) ,and run “networkcard1802″.after finishing this DOS run,please Power off of your laptop.(when you run this step,don’t instal wireless network card)2.open your laptop,and install wireless network card.(how to disassemble laptop)3.power on your laptop and install network card drive.now,the laptop shall not show 1802 error.
networkcard1802 download:Attention:if you install networkcard1802,do not upgrade bios,or the window XP was used for the initialization of system,otherwise please install networkcard1802 again.this computer program is not can from IBM office,if your laptop have any consequence.,I am not responsible,please serious consideration!
download address:networkcard1802 (0)
Related Posts:
The HP NC4400 Laptop Drive for Window XP
MACFlash—Prefessional Modify network card mac address tool
How to disassemble laptop ,step by step guide!
The most common of frequency value of laptop chip
IBM error fault code-IBM User Need to Know
How to search and replace your Laptop Motherboard
how to test laptop lcd screen
Laptop Troubleshooting -Laptop No Power Solution(1)
IBM ThinkPad T60 Laptop motherboard circuit diagram Download
How to buy and Replace a cover for your laptop
From laptop parts blog at www.laptoppartwholesale.com, post How to deal with minipci network card 1802 error
Post Footer automatically generated by wp-posturl plugin for wordpress.

Tags: 1802, error, IBM, network card

HP NC6000 Laptop motherboard ciruit diagram

HP NC6000 Laptop motherboard ciruit diagramif you need this HP NC6000 Laptop motherboard ciruit diagram,please register,i just send Laptop motherboard ciruit diagram to active member in the bolg.don’t ask me sent the ciruit diagram to you.if you real need Laptop motherboard ciruit diagram ,please make some contributions for the blog.you can write a skilled article or talk some thing about laptop.thanks
download: HP NC6000 circuit diagram (6)
Related Posts:
IBM ThinkPad T60 Laptop motherboard circuit diagram Download
Find a free download Space?
4 main data bus of Bios circuit diagram
IBM ThinkPad T40 Power control circuit diagram
HP NC6000 laptop motherboard MAX1987 chip poor Soldering
How to Upgrade THINKPAD 600E CPU To PⅢ 850
IBM ThinkPad T43 laptop motherboard fit into T40 case?
How to deal with minipci network card 1802 error
How to disassemble laptop ,step by step guide!
How to deal with HP DV2000 laptop GPU overheating
From laptop parts blog at www.laptoppartwholesale.com, post HP NC6000 Laptop motherboard ciruit diagram
Post Footer automatically generated by wp-posturl plugin for wordpress.

Tags: ciruit diagram, HP, laptop motherboard, NC6000

HP NC6000 Laptop motherboard ciruit diagram

HP NC6000 Laptop motherboard ciruit diagramif you need this HP NC6000 Laptop motherboard ciruit diagram,please register,i just send Laptop motherboard ciruit diagram to active member in the bolg.don’t ask me sent the ciruit diagram to you.if you real need Laptop motherboard ciruit diagram ,please make some contributions for the blog.you can write a skilled article or talk some thing about laptop.thanks
download: HP NC6000 circuit diagram (6)
Related Posts:
IBM ThinkPad T60 Laptop motherboard circuit diagram Download
Find a free download Space?
4 main data bus of Bios circuit diagram
IBM ThinkPad T40 Power control circuit diagram
HP NC6000 laptop motherboard MAX1987 chip poor Soldering
How to Upgrade THINKPAD 600E CPU To PⅢ 850
IBM ThinkPad T43 laptop motherboard fit into T40 case?
How to deal with minipci network card 1802 error
How to disassemble laptop ,step by step guide!
How to deal with HP DV2000 laptop GPU overheating
From laptop parts blog at www.laptoppartwholesale.com, post HP NC6000 Laptop motherboard ciruit diagram
Post Footer automatically generated by wp-posturl plugin for wordpress.

Tags: ciruit diagram, HP, laptop motherboard, NC6000